Saturday, 3 February 2018

DHCP

Dynamic Host Configuration Protocol

DHCP (Dynamic Host Configuration Protocol) is a protocol used to provide quick, automatic, and central management for the distribution of IP addresses within a network.
DHCP is also used to configure the proper subnet mask, default gateway, and DNS server information on the device.















Recall that DHCP clients broadcast their DHCPDiscover packets, when searching for a DHCP server. What would happen if the DHCP server is on a different network, separated from the clients by a router? Routers, by default, will never forward a broadcast. Thus, in the above example, the client would never be able to reach the DHCP server to acquire its IP address. That is, unless the ip helper-address command is used.






Network Routing

Saturday, 27 January 2018

Telnet


What is Telnet?
 
Telnet is a terminal emulation program for TCP/IP networks such as the Internet. The Telnet program runs on your computer and connects your PC to a server on the network. You can then enter commands through the Telnet program and they will be executed as if you were entering them directly on the server console. This enables you to control the server and communicate with other servers on the network. To start a Telnet session, you must log in to a server by entering a valid username and password. Telnet is a common way to remotely control Web servers. Telnet use port 23.



The Telnet Protocol

The Telnet protocol is designed to provide a bi-directional, eight-bit byte oriented communications facility to allow for a standard method of interfacing terminal devices and processes. Additional information on the Telnet protocol specification can be found RFC854.

 


Network Routing Switching

Friday, 26 January 2018

VTP (VLAN Trunking Protocol)



Dynamic Trunking Protocol (DTP) 

Recall that a trunk’s frame tagging protocol can be auto negotiated, through the use of the Dynamic Trunking Protocol (DTP). DTP can also negotiate whether a port becomes a trunk at all.
Examples demonstrated how to manually configure a port to trunk:
Switch(config)# interface gi2/24
Switch(config-if)# switchport mode trunk

DTP has two modes to dynamically decide whether a port becomes a trunk:

Desirable – the port will actively attempt to form a trunk with the remote switch. This is the default setting.
Auto – the port will passively wait for the remote switch to initiate the trunk.

What is VTP (VLAN Trunking Protocol)?
VTP (VLAN Trunking Protocol) is a Cisco proprietary protocol used by Cisco switches to exchange VLAN information. With VTP, you can synchronize VLAN information (like VLAN ID or VLAN name) with switches inside the same VTP domain.

VTP Versions
There are three versions of VTP. VTP version 1 supports the standard 1 – 1005 VLAN range. VTP version 1 is also default on Catalyst switches.

VTP version 2 introduces some additional features:

Token Ring support
VLAN consistency checks

Domain-independent transparent pass through VTPv1 and v2 are not compatible. The VTP version is dictated by the VTP server, discussed in detail shortly. If the VTP server is configured for VTPv2, all other switches in the VTP domain will change to v2 as well. Until recently, VTP Version 3 was supported on only limited Cisco switch platforms. VTPv3 was built to be flexible, and can forward both VLAN and other database information, such as Multiple Spanning Tree (MST) protocol.

Other enhancements provided by VTPv3 include:

Support for the extended 1006-4094 VLAN range.
Support for private VLANs.
Improved VTP authentication.
Protection from accidental database overwrites, by using VTP primary and secondary servers.
Ability to enable VTP on a per-port basis.

Each switch can use one of three different VTP modes:

1. VTP client mode – a switch using this mode can’t change its VLAN configuration. That means that a VTP client switch can’t create or delete VLANs. Received VTP updates are processed and forwarded.

2. VTP server mode – a switch using this mode can create and delete VLANs. A VTP server switch will propagate VLAN changes. This is the default mode for Cisco switches.

3. VTP transparent mode – a switch using this mode doesn’t share its VLAN database, but it forwards received VTP advertisements. You can create and delete VLANs on a VTP transparent switch, but the changes are not sent to other switches.


VTP Server
VTP Client
VTP Transparent
Create/Modify/Delete VLANs
Yes
No
Only local
Synchronizes itself
Yes
Yes
No
Forwards advertisements
Yes
Yes
Yes

Switching

Thursday, 25 January 2018

Switching basics



Local Area Network (LAN) Switches support different Switching Methods. Important Switching Methods are store and forward, cut-through and fragment-free. Switching Methods determine how a switch receives, processes, and forwards a Layer 2 Ethernet frame.
Store and Forward Switching
In Store and forward switching, Switch copies each complete Ethernet frame into the switch memory and computes a Cyclic Redundancy Check (CRC) for errors. If a Cyclic Redundancy Check (CRC) error is found, the Ethernet frame is dropped and if there is no Cyclic Redundancy Check (CRC) error, the switch forwards the Ethernet frame to the destination device. Store and forward switching can cause delay in switching since Cyclic Redundancy Check (CRC) is calculated for each Ethernet frame.
Cut-through Switching
In cut-through switching, the switch copies into its memory only the destination MAC address (first 6 bytes of the frame) of the frame before making a switching decision. A switch operating in cut-through switching mode reduces delay because the switch starts to forward the Ethernet frame as soon as it reads the destination MAC address and determines the outgoing switch port. Problem related with cut-through switching is that the switch may forward bad frames.
Fragment-Free Switching
Fragment-free (runt less switching) switching is an advanced form of cut-through switching. The switches operating in cut-through switching read only up to the destination MAC address field in the Ethernet frame before making a switching decision. The switches operating in fragment-free switching read at least 64 bytes of the Ethernet frame before switching it to avoid forwarding Ethernet runt frames (Ethernet frames smaller than 64 bytes).
Switching

Ad (728x90)

 

Copyright © Technical Agenda™ is a registered trademark.
Designed by Templateism | Distributed by Templatelib